Can you give the out pout of ifconfig?
I did ask you never give the output.
BCM 4313...
Re: BCM 4313...
hey there !
tia !
Code: Select all
ifconfig
enp4s0f2: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
ether 04:7d:7b:cf:41:c8 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1000 (Local Loopback)
RX packets 48 bytes 2800 (2.7 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 48 bytes 2800 (2.7 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
wlp9s0b1: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 192.168.2.101 netmask 255.255.255.0 broadcast 192.168.2.255
inet6 fe80::d09:53f2:3bd7:fc1c prefixlen 64 scopeid 0x20<link>
ether 84:4b:f5:4e:4f:79 txqueuelen 1000 (Ethernet)
RX packets 68761 bytes 71595153 (68.2 MiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 58392 bytes 7372668 (7.0 MiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
Re: BCM 4313...
Need to install on several lappys ( school LAB ) so this info can't wait more ...
Re: BCM 4313...
viewtopic.php?f=63&t=312#p1488geno_bsd wrote:no one ?
Re: BCM 4313...
I want your ifconfig output! I need to if the drver is loaded.
Re: BCM 4313...
I forgot to mention from GhostBSD. Not GNU/Linux.
Re: BCM 4313...
Code: Select all
# ifconfig
re0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=8209b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,WOL_MAGIC,LINKSTATE>
ether 04:7d:7b:cf:41:c8
inet 192.168.1.3 netmask 0xffffff00 broadcast 192.168.1.255
nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
media: Ethernet autoselect (100baseTX <full-duplex>)
status: active
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
options=600003<RXCSUM,TXCSUM,RXCSUM_IPV6,TXCSUM_IPV6>
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x2
inet 127.0.0.1 netmask 0xff000000
nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
Re: BCM 4313...
Oh true I just remember that none of the are loaded by default. You will need to add:
to /boot/loader.conf and probably install the firmware from ports.
You will find all you need here https://www.google.ca/search?q=freebsd+ ... sd+bcm4313.
Code: Select all
if_bwn_load="YES"
if_bwi_load="YES"
You will find all you need here https://www.google.ca/search?q=freebsd+ ... sd+bcm4313.