Search found 10 matches

by melloa
Mon Dec 03, 2018 3:16 pm
Forum: General support
Topic: [Solved] Terminal font
Replies: 3
Views: 556

Re: Terminal font

Hi Eric, Make sure that the font that you use for the terminal Monospace font and in Fixed width font is Monospace also. They were not (shouldn't that be the default for the install? set the font I mean; it was set to none on all of them.) I've tried to set all to courier and it didn't work, so set ...
by melloa
Mon Dec 03, 2018 2:24 pm
Forum: General support
Topic: [Solved] Terminal font
Replies: 3
Views: 556

[Solved] Terminal font

Guys, As I'm not sure if this is a video card, X, or something else, so I'm posting on the General Support. One thing that I've noticed and didn't get any help from searches is that the fonts on my terminal are not spaced correctly. In some cases it cover part of the previous character, in other add...
by melloa
Wed Nov 28, 2018 6:05 pm
Forum: Feedback
Topic: Support to 10Gb NICs during install
Replies: 0
Views: 367

Support to 10Gb NICs during install

Folks, Sure one can change the boot/loader.conf after install and set rc.conf to enable the interface, but would be great if the installer had support to Chelsios and Mellanox, so that NIC could be selected and configured from the get go. With the enterprises upgrading, 10Gb is getting less and less...
by melloa
Sat Nov 24, 2018 1:35 am
Forum: General Hardware Support
Topic: [Solved] LinksKey KVM switch
Replies: 2
Views: 500

Re: LinksKey KVM switch

Eric,
ericbsd wrote:
Fri Nov 23, 2018 6:35 pm

Code: Select all

echo 'ums_load="YES"' >> /boot/loader.conf
I am not sure if it will work for you.
Well ... it did :)

Thanks!
by melloa
Tue Nov 20, 2018 4:24 pm
Forum: General Hardware Support
Topic: [Solved] LinksKey KVM switch
Replies: 2
Views: 500

[Solved] LinksKey KVM switch

Hi guys, I use a LinksKey LKV-7308 KVM switch on my workstations and can't make the mouse work with GhostBSD. I have to connect a 2nd mouse to it to be able to use it. I do see this on dmesg with the KVM connected: ugen2.3: <vendor 0x2188 USB OPTICAL MOUSE> at usbus2 ums0 on uhub4 ums0: <vendor 0x21...
by melloa
Tue Nov 20, 2018 4:11 pm
Forum: General Hardware Support
Topic: Problem trying to install ghostbsd on SSD disk !!
Replies: 8
Views: 2458

Re: Problem trying to install ghostbsd on SSD disk !!

Here no problem with the installation. I little slow, I think due to the speed of the DVD i've used. Installed on a Model Family: SandForce Driven SSDs Device Model: SanDisk SDSSDA120G Created a mirror zfs volume with other HDDs for storage and the system is stable and working fine. Little issue wit...
by melloa
Tue Nov 20, 2018 4:03 pm
Forum: Networking
Topic: System freezes after cxgb driver is loaded
Replies: 1
Views: 532

Re: System freezes after cxgb driver is loaded

Closing the freezing issue as it's gone with the new T3610 I got for GhostBSD. NIC is detected without any issues: cxgb0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 9000 options=6c07bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,TSO6,LRO,VLAN_HWTSO,LINKSTATE...
by melloa
Tue Nov 06, 2018 1:56 pm
Forum: General Questions
Topic: Add 2nd disk
Replies: 2
Views: 2140

Re: Add 2nd disk

I've installed on the SSD and have a 3TiB HD I want to add for storage. No ZFS.
by melloa
Sun Nov 04, 2018 1:56 am
Forum: General Questions
Topic: Add 2nd disk
Replies: 2
Views: 2140

Add 2nd disk

Folks,

Got GhostBSD installed on a SSD and got a disk I finished burning to install. Can't find a way to do it from the GUI. Can someone help me please?

Thanks,
Al
by melloa
Tue Oct 30, 2018 2:30 pm
Forum: Networking
Topic: System freezes after cxgb driver is loaded
Replies: 1
Views: 532

System freezes after cxgb driver is loaded

Folks, First of all I'd like to congratulate the project. Clean install, nice desktop. I'm putting it for a spin and migrate for sure. I did find two issues: mouse (on my KVM) is not working. Will get there later (I know this is the networking support :) ) After my fresh install, I've changed my /bo...